Skip to content
Snippets Groups Projects
  • Kim Namu's avatar
    2876f753
    ramips: mt7621: add support for Zbtlink ZBT-WG1608 · 2876f753
    Kim Namu authored
    
    Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
    modems.
    
    Specifications:
    * SoC: MediaTek MT7621A
    * RAM: 256/512 MiB
    * Flash: 16/32 MiB (SPI NOR)
    * Wi-Fi:
      * MediaTek MT7603E : 2.4Ghz
      * MediaTek MT7613BE : 5Ghz
    * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
    * M.2: 1x slot with USB&SIM
      * EM7455/EM12-G/EM160R/RM500Q-AE
    * USB: 1x 3.0 Type-A port
    * External storage: 1x microSD (SDXC) slot
    * UART: console (115200 baud)
    * LED:
      * 1 power indicator
      * 1 WLAN 2.4G controlled (wlan 2G)
      * 3 SoC controlled (wlan 5G, wwan, internet)
      * 5 per Eth phy (4xLAN + WAN)
    
    MAC Addresses:
    * LAN    : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
    * WAN    : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
    * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
    * 5 GHz  : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))
    
    Installation:
    * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
      be directly used to install OpenWrt. Firmware must be upgraded using the
      'force' and 'do not save configuration' command line options (or
      correspondig web interface checkboxes) since the vendor firmware is from
      the pre-DSA era.
    
    Recovery Mode:
     * Press reset button, power up the device, wait for about 10sec.
     * Upload sysupgrade image through the firmware recovery mode web page at
      192.168.1.1.
    
    Signed-off-by: default avatarKim Namu <namu@theseed.io>
    2876f753
    History
    ramips: mt7621: add support for Zbtlink ZBT-WG1608
    Kim Namu authored
    
    Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
    modems.
    
    Specifications:
    * SoC: MediaTek MT7621A
    * RAM: 256/512 MiB
    * Flash: 16/32 MiB (SPI NOR)
    * Wi-Fi:
      * MediaTek MT7603E : 2.4Ghz
      * MediaTek MT7613BE : 5Ghz
    * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
    * M.2: 1x slot with USB&SIM
      * EM7455/EM12-G/EM160R/RM500Q-AE
    * USB: 1x 3.0 Type-A port
    * External storage: 1x microSD (SDXC) slot
    * UART: console (115200 baud)
    * LED:
      * 1 power indicator
      * 1 WLAN 2.4G controlled (wlan 2G)
      * 3 SoC controlled (wlan 5G, wwan, internet)
      * 5 per Eth phy (4xLAN + WAN)
    
    MAC Addresses:
    * LAN    : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
    * WAN    : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
    * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
    * 5 GHz  : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))
    
    Installation:
    * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
      be directly used to install OpenWrt. Firmware must be upgraded using the
      'force' and 'do not save configuration' command line options (or
      correspondig web interface checkboxes) since the vendor firmware is from
      the pre-DSA era.
    
    Recovery Mode:
     * Press reset button, power up the device, wait for about 10sec.
     * Upload sysupgrade image through the firmware recovery mode web page at
      192.168.1.1.
    
    Signed-off-by: default avatarKim Namu <namu@theseed.io>
mt7621_zbtlink_zbt-wg1608-16m.dts 268 B