ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish

LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>

target/linux/ipq40xx/base-files/etc/board.d/01_leds

@@ -22,7 +22,8 @@ avm,fritzbox-4040)
 	ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x1e"
 	;;
 avm,fritzbox-7530 |\
-glinet,gl-b1300)
+glinet,gl-b1300 |\
+mikrotik,lhgg-60ad)
 	ucidef_set_led_wlan "wlan" "WLAN" "green:wlan" "phy0tpt"
 	;;
 edgecore,oap100)

target/linux/ipq40xx/base-files/etc/board.d/02_network

@@ -29,6 +29,7 @@ ipq40xx_setup_interfaces()
 	engenius,eap1300|\
 	engenius,emd1|\
 	meraki,mr33|\
+	mikrotik,lhgg-60ad|\
 	mikrotik,sxtsq-5-ac|\
 	netgear,ex6100v2|\
 	netgear,ex6150v2|\
@@ -190,6 +191,7 @@ ipq40xx_setup_macs()
 		lan_mac=$(macaddr_add $wan_mac 1)
 		label_mac="$wan_mac"
 		;;
+	mikrotik,lhgg-60ad|\
 	mikrotik,sxtsq-5-ac)
 		lan_mac=$(cat /sys/firmware/mikrotik/hard_config/mac_base)
 		label_mac="$lan_mac"

target/linux/ipq40xx/base-files/lib/upgrade/platform.sh

@@ -133,6 +133,7 @@ platform_do_upgrade() {
 		nand_do_upgrade "$1"
 		;;
 	mikrotik,hap-ac2|\
+	mikrotik,lhgg-60ad|\
 	mikrotik,sxtsq-5-ac)
 		[ "$(rootfs_type)" = "tmpfs" ] && mtd erase firmware
 		default_do_upgrade "$1"

target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-lhgg-60ad.dts

+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Robert Marko <robimarko@gmail.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "Mikrotik Wireless Wire Dish LHGG-60ad";
+	compatible = "mikrotik,lhgg-60ad";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		led-boot = &user;
+		led-failsafe = &user;
+		led-running = &user;
+		led-upgrade = &user;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+
+			/delete-node/ ethernet-phy@1;
+			/delete-node/ ethernet-phy@2;
+			/delete-node/ ethernet-phy@3;
+			/delete-node/ ethernet-phy@4;
+			/delete-node/ psgmii-phy@5;
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+			switch_lan_bmp = <0x0>; /* lan port bitmap */
+			switch_wan_bmp = <0x10>; /* wan port bitmap */
+		};
+
+		edma@c080000 {
+			status = "okay";
+			phy-mode = "rgmii-id";
+			qcom,num_gmac = <1>;
+			qcom,single-phy;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power: power {
+			label = "blue:power";
+			gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+			panic-indicator;
+		};
+
+		user: user {
+			label = "yellow:user";
+			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan {
+			label = "green:wlan";
+			gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+		};
+
+		align-left {
+			label = "green:align-left";
+			gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		align-right {
+			label = "green:align-right";
+			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan-rx {
+			label = "green:align-down";
+			gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan-tx {
+			label = "green:align-up";
+			gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi-0-pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	m25p80@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "Qualcomm";
+				reg = <0x0 0x80000>;
+				read-only;
+			};
+
+			partition@80000 {
+				compatible = "mikrotik,routerboot-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				label = "RouterBoot";
+				reg = <0x80000 0x80000>;
+				read-only;
+
+				hard_config {
+					read-only;
+					size = <0x2000>;
+				};
+
+				dtb_config {
+					read-only;
+				};
+
+				soft_config {
+				};
+			};
+
+			partition@100000 {
+				compatible = "mikrotik,minor";
+				label = "firmware";
+				reg = <0x100000 0xf00000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		/* wil6210 802.11ad card */
+		wifi: wifi@1,0 {
+			status = "okay";
+			/* wil6210 driver has no compatible */
+			reg = <0x00010000 0 0 0 0>;
+		};
+	};
+};
+
+&gmac0 {
+	qcom,phy_mdio_addr = <0>;
+	qcom,poll_required = <1>;
+	vlan_tag = <0 0x20>;
+};

target/linux/ipq40xx/image/mikrotik.mk

@@ -40,6 +40,14 @@ define Device/mikrotik_hap-ac3
 endef
 TARGET_DEVICES += mikrotik_hap-ac3
 
+define Device/mikrotik_lhgg-60ad
+	$(call Device/mikrotik_nor)
+	DEVICE_MODEL := Wireless Wire Dish LHGG-60ad
+	DEVICE_DTS := qcom-ipq4019-lhgg-60ad
+	DEVICE_PACKAGES += -kmod-ath10k-ct -ath10k-firmware-qca4019-ct kmod-wil6210
+endef
+TARGET_DEVICES += mikrotik_lhgg-60ad
+
 define Device/mikrotik_sxtsq-5-ac
 	$(call Device/mikrotik_nor)
 	DEVICE_MODEL := SXTsq 5 ac (RBSXTsqG-5acD)

target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -902,11 +902,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -58,6 +58,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-habanero-dvk.dtb \
 +	qcom-ipq4019-hap-ac3.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
++	qcom-ipq4019-lhgg-60ad.dtb \
 +	qcom-ipq4019-mr8300.dtb \
 +	qcom-ipq4019-pa2200.dtb \
 +	qcom-ipq4019-r619ac-64m.dtb \

target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch

@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,67 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -55,6 +55,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-fritzrepeater-3000.dtb \
 +	qcom-ipq4019-hap-ac3.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
++	qcom-ipq4019-lhgg-60ad.dtb \
 +	qcom-ipq4019-mr8300.dtb \
 +	qcom-ipq4019-e2600ac-c1.dtb \
 +	qcom-ipq4019-e2600ac-c2.dtb \