fixes #12754

Signed-off-by:  <rq@akl.lt>

SVN-Revision: 35019

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 35018

SVN-Revision: 35016

SVN-Revision: 35015

I wanted to use some statistics from /sys/kernel/debug/ieee80211,
so I enabled PACKAGE_MAC80211_DEBUGFS.  But I could not use it,
because CONFIG_KERNEL_DEBUG_FS was not set and it's a little bit
hidden. After manually setting CONFIG_KERNEL_DEBUG_FS to y,
everything was fine. This patch automatically selects
CONFIG_KERNEL_DEBUG_FS if PACKAGE_MAC80211_DEBUGFS is set.

Additionally, the help text says "Say N unless you know you need this.",
but it's default y. This help text is copied verbatim from the
kernel's Kconfig and not true for us. So remove this part of the
help text

Signed-off-by: Stefan Hellermann <stefan@the2masters.de>

SVN-Revision: 35014

SVN-Revision: 35013

firewall: Add ULA site border for IPv6 traffic This prevents private traffic from leaking out to the internet

SVN-Revision: 35012

Add Huawei EchoLife HG556a support.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo@openwrt.org: added some code style fixes]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35011

Allow bcm63xxpart to receive a caldata offset if calibration data is contained in flash.

Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>

SVN-Revision: 35010

3.6 is tested enough to be considered stable.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 35009

iwinfo: don't use the txpower value from debugfs for now, it does not match the values reported via wext

SVN-Revision: 35007

Delete +lua from libiwinfo-lua.

Signed-off-by: Stefan Hellermann <stefan@the2masters.de>

SVN-Revision: 35005

SVN-Revision: 35001

remove firmware for LP-Phy core rev 14, I have never seen such a device.

SVN-Revision: 35000

SVN-Revision: 34999

SVN-Revision: 34998

This is based on a patch send by Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34997

This adds diag leds/buttons support for Linksys E1000 V1. It worked on
my router, however it may need some tweaking by people more familiar
with openwrt and c to make it fit for commiting.

Thank you hhm for this patch.

SVN-Revision: 34996

This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.

Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.

SVN-Revision: 34995

SVN-Revision: 34994

In addition check_module is not needed, nobody checks the return value.

SVN-Revision: 34993

I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD.  This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.

In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex.  I was not able to isolate the source of the problem
(this patch, driver or H/W limitation).  The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).

I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34992

This is in part based on a patch send by Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34991

Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK).  IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34990

This was party inspirited by patches send by Nathan Hintz <nlhintz@hotmail.com>

SVN-Revision: 34989

This is the version like it was send for mainline inclusion.

SVN-Revision: 34988

SVN-Revision: 34987

SVN-Revision: 34986

ipv6-support: Update iteration * Add support for blocking forwarding while address assignments * Fix relay restarting function

SVN-Revision: 34985

SVN-Revision: 34984

SVN-Revision: 34983

iwinfo: replace more wext calls with nl80211 equivalents, attempt to infer nl80211 tx power from debugfs before querying wext

SVN-Revision: 34982

SVN-Revision: 34981

SVN-Revision: 34979

Fixes #12346.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 34975

Neither --create-backup nor --restore-backup need an image name (following
the backup filename). Treat them in uniform way.

Mostly fixes #12346.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 34974

SVN-Revision: 34972

SVN-Revision: 34971

	- introduce "list interface" options to specify the ifaces to listen on, takes uci- or network device name
	- set the default system description to distrib @ hostname, e.g. "OpenWrt Barrier Breaker r34744 @ vbox"
	- introduce "option lldp_description" to override the automatically generated description

SVN-Revision: 34970

RT5350 frame engine need reset frame engine and embedded switch together.

Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>

SVN-Revision: 34969