JCG JHR-AC876M is an AC2600M router

Hardware specs:
  SoC: MT7621AT
  2.4GHz: MT7615N 4x4 @ PCIe0
  5GHz: MT7615N 4x4 @ PCIe1
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  USB 2.0 and 3.0 ports
  6 LEDs, 3 of which are connected to SoC GPIO
  Reset and WPS buttons

Flash instructions:
Stock to OpenWrt:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings

OpenWrt to stock:
  Push and hold the reset button for 5s while power cycling to
  enter recovery mode;
  Visit 192.168.1.1 and upload stock firmware

MAC addresses map:
  0x0004  *:1c  wlan2g/wan/label
  0x8004  *:20  wlan5g
  0xe000  *:1b  lan
  0xe006  *:1a  not used in stock fw

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>

This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.

This also changes the only occurence of the variable, for Cudy WR1000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- UART:
  - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>

This does several trivial DTS style improvements:

- Move device name compatible to DTS files (and fix compatible in
  11acnas.dts)
- Remove xhci node as status is set to okay in mt7621.dtsi already
- 0x0 instead of 0x0000
- Simplify state_default node definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7603EN
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x 3.0
- UART:
  - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.

MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)

Installation via web interface:
1.  Access web admin page and turn on "OpenWrt UI mode".
2.  Flash sysupgrade image through LuCI, with the "Keep settings" option
    OFF.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.
    Make sure to NOT preserve settings.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

Hardware:

  Allwinner H3 upto 1.2GHz
  512MB DDR3 RAM
  8GB on-board eMMC - mountable, can be used as boot with custom boot.scr
  microSD-card slot
  WiFi 802.11n (AP6212A) - working
  Bluetooth (AP6212A) - not working for now
  Micro-USB OTG + 2*USB headers
  UART 3.3V - working
  GPIO/I2C/SPI 2.54mm headers

Standard sunxi SD-card installation procedure - copy image to SD card,
insert in into slot and boot. First time you will need UART adapter to
enable on-board wireless (or just build custom image with enabled WiFi).

To boot from eMMC:

  - boot from SD
  - copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2)
  - mount eMMC boot partition and replace boot script on it
  - unmount, reboot

To use i2c, spi and more uarts - replace dtb on boot partition with
fixed one (use dtc or fdt-tools).

Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
[rebase onto device name consolidation patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The device part in the SUNXI_DTS variable always corresponds to
device node name. This is another redundancy that can be removed
by calculating the DTS name from a newly introduced SUNXI_SOC
variable and the node name.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This changes device definition to resemble the vendor_device scheme
already present for the majority of device compatible strings.

By doing this, we achieve several advantages at once:
- Image names and node names are more consistent with other targets.
- SUPPORTED_DEVICES can be set automatically for all but two cases.
- Image names and node names are in line with DEVICE_TITLEs.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.

Thanks to Josh4300 for testing on device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).

Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.

While at it, reorder the definitions to have order consistent, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09

The first value corresponds to the address set in hard_config 0x10.

That one is taken for the label MAC address.

Thanks to Martin Schiller for retrieving the information.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m

While at it, make some DT node labels consistent with the label
property.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.

The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The DTS variable has been removed in 402138d1 ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.

Remove it now since we are not using this variable.

This must _not_ be backported to 19.07, where the variable is still
in use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.

Port order checked on both devices.

Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

Current OpenWrt MAC setup:
eth0             &rom 0xf100    :48
eth0.2           eth0+1         :49
wlan0 (5 GHz)    &radio 0x8004  different OUI
wlan1 (2.4 GHz)  &radio 0x4     same OUI as wlan0

Label MAC address corresponds to eth0 (&ethernet).

No additional addresses found in hexdump of rom/radio.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci".

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>

Refreshed all patches.

Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch

Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

Refreshed all patches.

Altered patches:
- 400-mtd-add-rootfs-split-support.patch

Compile-tested on: none
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Having legacy PTYs enabled causes problems with procd-hotplug.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.

Experimentally determined:

Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU

Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.

Also change "0" to "0x0" in the same files for consistency.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

The Mikrotik RBM33G has only 2 LAN ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4

Physical Port	Switch port
WAN             0
LAN 3           1
LAN 4           2
LAN 1           3
LAN 2           4
(not used)      5
CPU             6

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>