- Feb 10, 2022
-
-
DENG Qingfang authored
Support MT7530 PHY link change interrupts, and enable for MT7621. For external MT7530, a GPIO IRQ line is required, which is board-specific, so it should be added to each DTS. In case the interrupt-controller property is missing, it will fall back to polling mode. Signed-off-by:DENG Qingfang <dqfext@gmail.com>
-
Paul Spooren authored
Tested-by:
Chuanhong Guo <gch981213@gmail.com> Signed-off-by:
Paul Spooren <mail@aparcar.org>
-
- Feb 09, 2022
-
-
DENG Qingfang authored
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530 and MT7531. Fix some link up/down issues. The errornous check for the PHY mode which broke things with MT7531 has been removed as suggested by patch net: phy: mediatek: remove PHY mode check on MT7531 As a result, things are working fine now on MT7622+MT7531 as well. Signed-off-by:
Daniel Golle <daniel@makrotopia.org> Tested-by:
Arınç ÜNAL <arinc.unal@arinc9.com> Tested-by:
Stijn Tintel <stijn@linux-ipv6.be>
-
Jo-Philipp Wich authored
The contents do not apply anymore now that the switch to Github issue has been decided. Signed-off-by:Jo-Philipp Wich <jo@mein.io>
-
Rui Salvaterra authored
The kernel configuration allows us to select a default qdisc. Let's do this for 5.10 (as 5.4 is on its way out) and get rid of the hacky patch we've been carrying. Acked-by:
Rui Salvaterra <rsalvaterra@gmail.com>
-
- Feb 08, 2022
-
-
Jo-Philipp Wich authored
a317c17 compiler: fix incorrect loop break targets Signed-off-by: -
Sungbo Eo authored
Commit f4a79148 ("ramips: add support for ipTIME AX2004M") was reverted due to KERNEL_LOADADDR leakage, and it seems the problem can be mitigated by moving the variable definition into Device/Default. By this, KERNEL_LOADADDR redefined in a device recipe will not be leaked into the subsequent device recipes anymore and thus will remain as a per-device variable. Ref: cd6a6e30 ("Revert "ramips: add support for ipTIME AX2004M"") Signed-off-by:
Sungbo Eo <mans0n@gorani.run>
-
Mike Lothian authored
Increase the available flash memory size in Netgear R7800 by repurposing the unused "netgear" partition that is located after the firmware partition. Available flash space for kernel+rootfs+overlay increases by 68 MB from 32 MB to 100 MB. In a typical build, overlay space increases from 15 to 85, increasing the package installation possibilities greatly. Reverting to the OEM firmware is still possible, as the OEM firmware contains logic to initialise the "netgear" partition if its contents do not match expectations. In OEM firmware, "netgear" contains 6 UBI sub-partitions that are defined in /etc/netgear.cfg and initialisation is done by /etc/preinit This is based on https://github.com/openwrt/openwrt/commit/fb8a578aa70572b3e56b64d296e22c2931e77b69 Signed-off-by:
Mike Lothian <mike@fireburn.co.uk>
-
Leonardo Mörlein authored
When the uci configuration is created automatically during a very early stage, where no entropy daemon is set up, generating the key directly is not an option. Therefore we allow to set the private_key to "generate" and generate the private key directly before the interface is taken up. Signed-off-by:
Leonardo Mörlein <me@irrelefant.net> Tested-by:
Jan-Niklas Burfeind <git@aiyionpri.me>
-
- Feb 07, 2022
-
-
David Bauer authored
Refresh patches after updating to hostapd v2.10. Signed-off-by:David Bauer <mail@david-bauer.net>
-
David Bauer authored
Upstreamed patches: 020-mesh-make-forwarding-configurable.patch e6db1bc5da3fd7d5f4dba24aa102543b4749912f 550-WNM-allow-specifying-dialog-token.patch 979f19716539362f8ce60a77bf1b88fdcf5ba8e5 720-ACS-fix-channel-100-frequency.patch 2341585c349231af00cdef8d51458df01bc6965f 741-proxyarp-fix-compilation-with-Hotspot-2.0-disabled.patch 08bdf4f90de61a84ed8f4dd918272dd9d36e2e1f Compile-tested: wpad-wolfssl hostapd-openssl Run-tested: ath79-generic Signed-off-by:
-
Jo-Philipp Wich authored
a0518b6 fw4: gracefully handle unsupported hardware offloading ac99eba init: fix boot action in init script Signed-off-by: -
Felix Fietkau authored
Simplifies switching to different channels when on >= VHT80 Signed-off-by:Felix Fietkau <nbd@nbd.name>
-
Jo-Philipp Wich authored
909f2a0 ucode: adjust to latest ucode api 4c532bf ucode: add ucode interpreter plugin 9c6ba38 treewide: adjust ubus object type names 75a96dc build: honour CMake install prefix in hardcoded paths Signed-off-by: -
Jo-Philipp Wich authored
2f8b136 main: fix leaking -p/-s argument values 881fd3b ucode: adjust to latest ucode api 8b2868e file: specify UTF-8 as charset for dirlists, add option to override 3a5bd84 main: add ucode options to help text 16aa142 examples: add ucode handler example 3ceccd0 ucode: add ucode plugin support f0f1406 examples: add example Lua handler script 9e87095 listen: avoid invalid memory access Signed-off-by: -
Jo-Philipp Wich authored
b54f462 fw4: parse traffic rules before forwarding rules 4d5af8b fw4: consolidate helper code 300c737 fw4: fix applying zone family restrictions to forwardings eb9c25a tests: implement fs.opendir() mock interface d30ff48 tests: fix mocked fs.popen() trace log 52831a0 fw4: improve flowtable handling 7cb10c8 fw4: disable "flow_offloading_hw" option for now b2241a1 fw4: fix enabling NAT reflection rules for DNATs without explicit family Signed-off-by: -
Jo-Philipp Wich authored
11adf0c source: convert source objects into proper uc_value_t type 3a49192 treewide: rework function memory model 7edad5c tests: add functional tests for builtin functions d5003fd lib: fix leaking tokener in uc_json() on parse exception 5d0ecd9 lib: fix infinite loop on empty regexp matches in uc_replace() 3ad57f1 lib: fix infinite loop on empty regexp matches in uc_match() 32d596d lib: fix infinite loop on empty regexp matches in uc_split() 3e3f38d vm: ensure consistent trace output between gcc and clang compiled ucode 3600ded vm: fix leaking function value on call exception 3059295 vm: NULL-initialize pointer to make cppcheck happy 98e59bf source: zero-initialize conversion union to make cppcheck happy 7a65c14 run_tests.sh: change workdir to testcase directory during execution afec8d7 run_tests.sh: support placing supplemental testcase files 3ada6e0 run_tests.sh: always treat outputs as text data 2cb627f program: rename bytecode load/write functions, track path of executed file 1094ffa lib: fix memory leak in uc_require_ucode() Signed-off-by: -
Jo-Philipp Wich authored
fd4c9e1 system-linux: expose hw-tc-offload ethtool feature in device status dump 3d76f2e system-linux: add wrapper function for creating link config messages 88af2f1 system-linux: delete bridge devices using netlink 85c3548 system-linux: create bridge devices using netlink Signed-off-by: -
Jo-Philipp Wich authored
This reverts commit 8de901cc. Apparently this update breaks tools building. Signed-off-by:
-
- Feb 06, 2022
-
-
Raymond Wang authored
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports. Alongside the general model, it has three carrier customized models: CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom) Specifications: - SoC: MediaTek MT7621AT - RAM: 256MB DDR3 (ESMT M15T2G16128A) - Flash: 128MB NAND (ESMT F59L1G81MB) - Ethernet: 1000Base-T x4 (MT7530 SoC) - WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN) - LEDs: System (Blue, Yellow), Internet (Blue, Yellow) - Buttons: Reset, WPS - UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1) - Power: 12VDC, 1A Jailbreak Notes: 1. Get shell access. 1.1. Get yourself a wireless router that runs OpenWrt already. 1.2. On the OpenWrt router: 1.2.1. Access its console. 1.2.2. Create and edit /usr/lib/lua/luci/controller/admin/xqsystem.lua with the following code (exclude backquotes and line no.): ``` 1 module("luci.controller.admin.xqsystem", package.seeall) 2 3 function index() 4 local page = node("api") 5 page.target = firstchild() 6 page.title = ("") 7 page.order = 100 8 page.index = true 9 page = node("api","xqsystem") 10 page.target = firstchild() 11 page.title = ("") 12 page.order = 100 13 page.index = true 14 entry({"api", "xqsystem", "token"}, call("getToken"), (""), 103, 0x08) 15 end 16 17 local LuciHttp = require("luci.http") 18 19 function getToken() 20 local result = {} 21 result["code"] = 0 22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i 's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop bear start;" 23 LuciHttp.write_json(result) 24 end ``` 1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token It should give you a respond like this: {"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."} If so, continue; Otherwise, check the file, reboot the rout- er, try again. 1.2.4. Set wireless network interface's IP to 169.254.31.1, turn off DHCP of wireless interface's zone. 1.2.5. Connect to the router wirelessly, manually set your access device's IP to 169.254.31.3, make sure http://169.254.31.1/cgi-bin/luci/api/xqsystem/token still have a similar result as 1.2.3 shows. 1.3. On the Xiaomi CR660x: 1.3.1. Login to the web interface. Your would be directed to a page with URL like this: http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r- outer 1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME} {PASSWORD} be your OpenWrt router's SSID and password: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy- stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO- RD} It should return 0. 1.3.3. Browse this URL with {STOK} from 1.3.1: http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy- stem/oneclick_get_remote_token?username=xxx&password=xxx&- nonce=xxx 1.4. Before rebooting, you can now access your CR660x via SSH. For CR6606, you can calculate your root password by this project: https://github.com/wfjsw/xiaoqiang-root-password, or at https://www.oxygen7.cn/miwifi . The root password for carrier-specific models should be the admi- nistration password or the default login password on the label. It is also feasible to change the root password at the same time by modifying the script from step 1.2.2. You can treat OpenWrt Router however you like from this point as long as you don't mind go through this again if you have to expl- oit it again. If you do have to and left your OpenWrt router unt- ouched, start from 1.3. 2. There's no official binary firmware available, and if you lose the content of your flash, no one except Xiaomi can help you. Dump these partitions in case you need them: "Bootloader" "Nvram" "Bdata" "crash" "crash_log" "firmware" "firmware1" "overlay" "obr" Find the corespond block device from /proc/mtd Read from read-only block device to avoid misoperation. It's recommended to use /tmp/syslogbackup/ as destination, since files would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP Keep an eye on memory usage though. 3. Since UART access is locked ootb, you should get UART access by modify uboot env. Otherwise, your router may become bricked. Excute these in stock firmware shell: a. nvram set boot_wait=on b. nvram set bootdelay=3 c. nvram commit Or in OpenWrt: a. opkg update && opkg install kmod-mtd-rw b. insmod mtd-rw i_want_a_brick=1 c. fw_setenv boot_wait on d. fw_setenv bootdelay 3 e. rmmod mtd-rw Migrate to OpenWrt: 1. Transfer squashfs-firmware.bin to the router. 2. nvram set flag_try_sys1_failed=0 3. nvram set flag_try_sys2_failed=1 4. nvram commit 5. mtd -r write /path/to/image/squashfs-firmware.bin firmware Additional Info: 1. CR660x series routers has a different nand layout compared to other Xiaomi nand devices. 2. This router has a relatively fresh uboot (2018.09) compared to other Xiaomi devices, and it is capable of booting fit image firmware. Unfortunately, no successful attempt of booting OpenWrt fit image were made so far. The cause is still yet to be known. For now, we use legacy image instead. Signed-off-by:Raymond Wang <infiwang@pm.me>
-
Jakob Riepler authored
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi integrated antenna built around the Atheros AR9344 SoC. It is very similar to the SXT Lite5 series which this patch is based upon. Specifications: - SoC: Atheros AR9344 - RAM: 64 MB - Storage: 16 MB SPI NOR - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port, 8-32 Vdc PoE in - 8 user-controllable LEDs: - 1x power (blue) - 1x user (white) - 1x ethernet (green) - 5x rssi (green) See https://mikrotik.com/product/RBLHG-5nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform a sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common . Signed-off-by:Jakob Riepler <jakob+openwrt@chaosfield.at>
-
Wenli Looi authored
Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by:Wenli Looi <wlooi@ucalgary.ca>
-
Wenli Looi authored
Based on wikidevi, QCN5502 is a "Dragonfly" like QCA9561 and QCA9563. Treating it as QCA956x seems to work. Signed-off-by: -
Saiful Islam authored
Specifications: - AR9344 SoC, 8 MB nor flash, 64 MB DDR2 RAM - 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps - 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100 - 1x WAN, 4x LAN, Wifi, PWR, WPS, SYSTEM Leds - Reset/WPS button - Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1 MAC addresses as verified by OEM firmware: vendor OpenWrt address LAN eth0 label WAN eth1 label + 1 WLAN phy0 label The label MAC address was found in u-boot 0x1fc00. Installation: To install openwrt, - set the device's SSID to each of the following lines, making sure to include the backticks. - set the ssid and click save between each line. `echo "httpd -k"> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -r&">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -k">> /tmp/s` `echo "sleep 10">> /tmp/s` `echo "httpd -f">> /tmp/s` `sh /tmp/s` - Now, wait 60 sec. - After the reboot sequence, the router may have fallen back to its default IP address with the default credentials (admin:admin). - Log in to the web interface and go the the firmware upload page. Select "openwrt-ath79-generic-tplink_tl-wr841hp-v2-squashfs-factory.bin" and you're done : the system now accepts the openwrt. Forum support topic: https://forum.openwrt.org/t/support-for-tplink-tl-wr841hp-v2/69445/ Signed-off-by:
Saiful Islam <si87868@gmail.com>
-
Rosen Penev authored
Switched to building with meson as it's faster and does not need a dependency on cmake, which takes a long time to build. Signed-off-by:Rosen Penev <rosenp@gmail.com>
-
Rosen Penev authored
When using a non default MESON_HOST_BUILD_DIR, HOST_BUILD_DIR is not appropriate to use. This change matches the target configure section. Signed-off-by: -
Rosen Penev authored
egrep is deprecated and replaced by grep -E. The latter is used throughout the tree. Signed-off-by: -
Rosen Penev authored
fgrep is deprecated and replaced by grep -F. The latter is used throughout the tree whereas this is the only usage of the former. Signed-off-by: -
Christian Lamparter authored
The recent device-tree modification that added pre-cal nvmem-cells pushed the device's kernel+dtb over the allotted 3072k KERNEL_SIZE. > WARNING: Image file tplink_vr2600v-uImage is too big: 3147214 > 3145728 There was a previous kernel partition size upgrade: commit 0c967d92 ("ipq806x: increase kernel partition size for the TP-Link Archer VR2600v") It has been seemingly upgraded from a 2048k KERNEL_SIZE in the past. The commit talks about using the MTD_SPLIT_TPLINK_FW. But looking at the image make recipe, there is no code that adds a TPLINK header. So instead the board will use "denx,umimage". This requires MTD_SPLIT_UIMAGE_FW, but this is present thanks to some NEC devices. (Maybe the MTD_CONFIG_ARGS can be removed as well? But it could be there because of the padding at the beginning. This needs testing.) Signed-off-by:
Christian Lamparter <chunkeey@gmail.com>
-
Ansuel Smith authored
Now that we have separate files for each kernel version, only the version/hash for the target kernel are available. This cause a missing hash error (and wrong kernel version) for bpf-headers when a testing kernel version is used for the current target. Fix this error by manually including the kernel version/hash file for the specific kernel version requested. Signed-off-by:Ansuel Smith <ansuelsmth@gmail.com>
-
- Feb 05, 2022
-
-
Hauke Mehrtens authored
This reverts commit 8b4cba53. This broke the mt7530 on Linksys e8450 (mt7622) for me. [ 1.312943] mt7530 mdio-bus:00 lan1 (uninitialized): failed to connect to PHY: -EINVAL [ 1.320890] mt7530 mdio-bus:00 lan1 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 0 [ 1.331163] mt7530 mdio-bus:00 lan2 (uninitialized): failed to connect to PHY: -EINVAL [ 1.339085] mt7530 mdio-bus:00 lan2 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 1 [ 1.349321] mt7530 mdio-bus:00 lan3 (uninitialized): failed to connect to PHY: -EINVAL [ 1.357241] mt7530 mdio-bus:00 lan3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 2 [ 1.367452] mt7530 mdio-bus:00 lan4 (uninitialized): failed to connect to PHY: -EINVAL [ 1.375367] mt7530 mdio-bus:00 lan4 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 3 [ 1.385750] mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL [ 1.393575] mt7530 mdio-bus:00 wan (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4 Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de>
-
Hauke Mehrtens authored
This reverts commit 3f4301e1. This broke the mt7530 on Linksys e8450 (mt7622) for me. [ 1.300554] mt7530 mdio-bus:00: no interrupt support Signed-off-by:
-
Stijn Tintel authored
Add a package for util-linux' ipcs command, to show information about System V inter-process communication facilities. Signed-off-by: -
DENG Qingfang authored
Support MT7530 PHY link change interrupts, and enable for MT7621. Signed-off-by:
-
DENG Qingfang authored
Add support for MediaTek Gigabit Ethernet PHYs found in MT7530. Fix some link up/down issues. Signed-off-by:
-
DENG Qingfang authored
Use hardware to forward multicast traffic instead of trapping to the host. Signed-off-by:
-
DENG Qingfang authored
Fix FDB learning bugs when VLAN filtering is enabled. Signed-off-by:
-
DENG Qingfang authored
Allow setting ageing time from 1 to 1,048,576 seconds. Signed-off-by:
-
DENG Qingfang authored
Allow MTU up to 2026 on mediatek, ramips/mt7621 targets. Signed-off-by:
-
Paul Spooren authored
Tested by multiple users and seems to work fine. Acked-by:
Daniel Danzberger <daniel@dd-wrt.com> Signed-off-by:
-
