- Refreshed all patches

Compile tested on: ar71xx
Runtime tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

mwlwifi was updated to a new stable. Included in this stable release are the
followin benefits:
- Fixed compiling for kernel 4.14
- Fixed crash on 88W8864 binary

Compiled and tested on: WRT3200ACM and WRT1900AC

Signed-off-by: Gabe Rodriguez <lifehacksback@gmail.com>

The patch breaks LED operation and has already been reverted in 4.4.121.
4.9.87 is still affected; revert it locally until the issue is sorted out
upstream.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

Option --client-cert-not-required DEPRECATED is deprecated in v2.4 and removed in OpenVPN 2.5.
Replaced by param --verify-client-cert none|optional|require in v2.4 see
https://community.openvpn.net/openvpn/wiki/

 DeprecatedOptions#a--client-cert-not-required

Signed-off-by: Christian Bayer <cave@cavebeat.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_	RELEASE increase]

The deletion of the mdio node childs was meant for testing and were
committed accidentally. Without the mdio nodes the network isn't
initialised.

While at it, remove the orphaned qcom-ipq4019-gl-b1300.dts as well.

Fixes: FS#1439
Signed-off-by: Mathias Kresin <dev@kresin.me>

* QCA IPQ4028
* 256 MB of RAM
* 32 MB of SPI NOR flash (mx25l25635e)
* 128 MB of SPI NAND flash (gd5f1gq4ucy1g)
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2 fully software controllable GPIO-LEDs
* 2 additional GPIO-LEDs which also affect the SIM card detection
* 1x button (reset)
* 1x GPIO buzzer
* 1x USB (xHCI)
* 1x NGFF (USB-only with Dual-SIM support, untested)
* TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC)
* 2x gigabit ethernet
  - phy@mdio4:
    + Manual: Ethernet port 0
    + gmac0 (ethaddr) in original firmware
    + 802.3af POE (HV version)
    + 24v passive POE (LV version)
  - phy@mdio3:
    + Manual: Ethernet port 1
    + gmac1 (eth1addr) in original firmware
* DC Jack connector
  + 24-56V (HV version)
  + 12-24V (LV version)

The SPI NAND flash isn't supported at the moment.

The bootloader has to be updated before OpenWrt is installed to fix a
reboot problem. The nor-ipq40xx-single.img from
https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware


has to be downloaded and the transfered in u-boot via TFTP

  set ipaddr 192.168.1.11
  set serverip 192.168.1.10
  ping ${serverip}
  tftpboot 0x84000000 nor-ipq40xx-single.img
  imgaddr=0x84000000 && source $imgaddr:script

The sysupgrade image can be installed directly on flash using u-boot:

  sf probe
  tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin
  sf erase 0x00180000 +$filesize
  sf write 0x84000000 0x00180000 $filesize
  bootipq

The initramfs image can be started using

  tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb
  set fdt_high 0x83000000
  bootm 0x82000000

The used SIM card slot can be changed using

  # slot 1 (also enables orange LED)
  echo 1 > /sys/class/gpio/gpio3/value
  # slot 2
  echo 0 > /sys/class/gpio/gpio3/value

It can be checked whether a SIM card is inserted in the current slot and
the red LED is subsequently on via:

  echo 2 > /sys/class/gpio/export
  cat /sys/class/gpio/gpio2/value

Signed-off-by: Sven Eckelmann <sven@narfation.org>

Some devices only boot when a special config is found in the image and
completely ignore the default entry during the selection. These devices can
now use the variable DEVICE_DTS_CONFIG in their device image definition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>

There are 2 ethernet ports on Nexx WT1520 and WT3020. These ethernet
ports are assigned as follows, and other ports cannot be used.

- WT1520:
  - port0 -> lan
  - port4 -> wan

- WT3020:
  - port0 -> wan
  - port4 -> lan

I dropped ports that cannot be used.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>

This reverts commit 43be5087.

The change is incompatible with the image builder code.
Luckily the RT-AC58U is no longer depending on the initramfs
being available for the target's image generation rules.

Reported-by: Venitex Aveon <aveon@aenote.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

The existing file is 0 byte. Replace the ASUS RT-AC58U board-2.bin with
the correct file.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Specification:
- SoC: Atheros AR9342
- Flash: 8 MiB
- RAM: 64 MiB
- UART: 1x UART on PCB - 115200 8N1
- Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A)

Doesn't work:
* Flash via TFTP with Ubiquiti Uboot

Installation via vendor firmware:
- upload factory image via webinterface

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>

Also fix minor coding style issue and one redeclaration.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

Fixes: 638e2193 ("tplink-safeloader: add support to split & extract firmwares")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

Those converted factory images can be used to regain the original
tp-link firmware.
Be aware of firmware upgrade which additional require changes of
other partition than os-image (kernel) & file-system (rootfs).
OEM factory images from tplink can change nearly all partitions.
However using those images, OpenWrt's sysupgrade will only
modify the partitions os-image and file-system.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

Split the oem firmware upgrade images into seperate files.
Useful when analysing oem firmware files.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

Hardware highlights:
- SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU
- RAM: (512MB or 1GB) DDR3 System Memory
- Storage: 32MB NOR (Cypress S25FL256S1)
           256MB NAND (Micron MT29F2G08ABBEAH4)
- Ethernet: 5 x 1G via QCA8337N
- USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket
- PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared)
- SIM Card Slot: 2 x Slot
- Buttons: Reset Button
- LEDs: 18x, 8x GPIO controllable
- Buzzer

The correct amount of RAM will be passed by the bootloader.

In contrast to the documentation provided by Compex, the third PCIe
doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST
for PCIe0 and PCIe2.

So far, no one was able to get USB 3.0 working with the 1GB RAM version,
while it works fine for my 512MB version. Since USB 3.0 doesn't work with
the Compex firmware for the 1G variant either, it could be a hardware
issue with these boards.

OpenWrt will be installed to the NAND flash. Make sure to have a full
working image on the NOR flash. It will be the backup in case anything
goes wrong.

It has been observed that an image loaded via tftpboot might have
bitflips. Hence the extra step to create a crc32 checksum to allow to
compare the checksum with the one from the source file prior to flashing.

In all cases it is necessary to set the following u-boot parameter to an
empty (whitespace) value, to ensure that the chosen bootargs of the dts
isn't overwritten or set to bogus - not working - values:

  (IPQ) # set bootargs " "
  (IPQ) # set fsbootargs " "
  (IPQ) # saveenv

The sysupgrade image can be installed directly on flash using u-boot (put
jumper in JP13 (leave JP9 open) to boot from nand):

  (IPQ) # set serverip 192.168.1.20
  (IPQ) # set ipaddr 192.168.1.1

  (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin
  (IPQ) # crc32 0x42000000 $filesize

  (IPQ) # nand erase 0x1340000 0x4000000
  (IPQ) # nand write 0x42000000 0x1340000 $filesize

The initramfs image can be started using:

  (IPQ) # set fdt_high 0x48000000
  (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb
  (IPQ) # bootm 0x44000000

Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>

Initialise the UBOOT variable by default. Otherwise it will be
unintended inherit to following images if set and causes an uboot build
where not required.

Signed-off-by: Mathias Kresin <dev@kresin.me>

This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.

Fixes: ac9bcefa ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

This patch adds support for Cisco Meraki MR33

hardware highlights:

SOC:	IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND:	128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH:	Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1:	QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2:	Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3:	Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS:	1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
	1 x Orange LED Fault Indicator (shared with LP5562)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON:	one Reset button
MISC:	Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
	AT24C64 8KiB EEPROM
	Kensington Lock

Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	1x4 0.1" header with half-height/low profile pins.
	The pinout is: VCC (little white arrow), RX, TX, GND.

Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>

Add images to do an installation via bootloader:
 0. open up the MR33 and connect the serial console.

 1. start the 2nd stage bootloader transfer from client pc:

  # ubootwrite.py --write=mr33-uboot.bin
  (The ubootwrite tool will interrupt the boot-process and hence
   it needs to listen for cues. If the connection is bad (due to
   the low-profile pins), the tool can fail multiple times and in
   weird ways. If you are not sure, just use a terminal program
   and see what the device is doing there.

 2. power on the MR33 (with ethernet + serial cables attached)
    Warning: Make sure you do this in a private LAN that has
    no connection to the internet.

 - let it upload the u-boot this can take 250-300 seconds -

 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
    (the u-boot is listening on 192.168.1.1)
    # tftp 192.168.1.1
    binary
    put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin

 4. wait for it to reboot

 5. connect to your MR33 via ssh on 192.168.1.1

For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33

>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)

Thanks to Jerome C. for sending an MR33 to Chris.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

Not all LED driver are using the label devicetree property for the led
name. Add support for the TI/National Semiconductor LP55xx Led Drivers,
which are using the chan-name property for the led name, as fallback.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Add a fucntion to get the a binary mac address from file. Use the new
function for mtd_get_mac_binary() to limit duplicate code.

Signed-off-by: Mathias Kresin <dev@kresin.me>

This patch adds support for ASUS RT-AC58U/RT-ACRH13.

hardware highlights:

SOC:	IPQ4018 / QCA Dakota
CPU:	Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:	128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR:	2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND:   128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH:    Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB:    1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:	one Reset and one WPS button
LEDS:	Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has an unpopulated
	1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
	PCB right next to the connector.

U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.

Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)

To install the image permanently, you have to do the following
steps in the listed order.

1. Open up the router.
   There are four phillips screws hiding behind the four plastic
   feets on the underside.

2. Connect the serial cable (See notes above)

3. Connect your router via one of the four LAN-ports (yellow)
   to a PC which can set the IP-Address and ssh and scp from.

   If possible set your PC's IPv4 Address to 192.168.1.70
   (As this is the IP-Address the Router's bootloader expects
   for the tftp server)

4. power up the router and enter the u-boot
   choose option 1 to upload the initramfs image. And follow
   through the ipv4 setup.

Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).

3. Connect to the OpenWrt running in RAM

   The default IPv4-Address of your router will be 192.168.1.1.

   1. Copy over the openwrt-sysupgrade.bin image to your router's
      temporary directory

   # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp

   2. ssh from your PC into your router as root.

   # ssh root@192.168.1.1

   The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.

   Once connected...: run the following commands on your temporary installation

   3. delete the "jffs2" ubi partition to make room for your new root partition

   # ubirmvol /dev/ubi0 --name=jffs2

   4. install OpenWrt on the NAND Flash.

   # sysupgrade -v /tmp/openwrt-sysupgrade.bin

   - This will will automatically reboot the router -

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

The image production rules does not have the initramfs-image
as a dependency. So, from make’s perspective initramfs
creation can run independently/in parallel with the image
generation code in the target's Makefile.

This is a problem for devices that have to use the initramfs
for the image creation and can lead to broken images.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

This patch adds the patch that was posted to ath10k-devel ML:
<https://patchwork.kernel.org/patch/10233491/

>
|From: Thomas Hebb <tommyhebb@gmail.com>
|Subject: [PATCH] ath10k: search all IEs for variant before falling back
|Date: Wed, 21 Feb 2018 11:43:39 -0500
|[...]
|This patch fixes the issue by first searching the entire file for the ID
|with variant, and searching for the fallback ID only if that search
|fails. It also includes some code cleanup in the area, as
|ath10k_core_fetch_board_data_api_n() no longer does its own string
|mangling to remove the variant from an ID, instead leaving that job to a
|new flag passed to ath10k_core_create_board_name().
|
|I've tested this patch on a QCA4019 and verified that the driver behaves
|correctly for 1) both fallback and variant BDFs present, 2) only fallback
|BDF present, and 3) no matching BDFs present.
|
|Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
|Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>

Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081
number, as it now ships with upstream.... But also because this patch
requires the change in ath10k_core_create_board_name().

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

Rename the dts file to match the used SoC type and drop the unnecessary
KERNEL_INSTALL from the image build code.

Remove the fixed rootfs and kernel partitions and create an image with
rootfs appended after kernel.

Setup a switch portmap matching the hardware and a default network/switch
configuration to make make the second lan port working. Use eth0 as lan
to have it consistent accross the target.

Use the power LED to indicate the boot status.

Sort the SoC entries within the dts by address and use dtc labels
whenever possible.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

This removes the block- and pagesize from the FritzBox 4040
image description, fixing incorrectly working sysupgrade.

With this commit, the default values for block- and pagesize are
used.

Signed-off-by: David Bauer <mail@david-bauer.net>
[chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

Sort the soc entries in the dts by address and use dtc labels whenever
possible.

Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an
IPQ4019.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

There's an interaction issue between the clk changes:"
clk: qcom: ipq4019: Add the apss cpu pll divider clock node
clk: qcom: ipq4019: remove fixed clocks and add pll clocks
" and the cpufreq-dt.

cpufreq-dt is now spamming the kernel-log with the following:

[ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP
for freq 761142857 (-34)

This only happens on certain devices like the Compex WPJ428
and AVM FritzBox!4040. However, other devices like the Asus
RT-AC58U and Meraki MR33 work just fine.

The issue stem from the fact that all higher CPU-Clocks
are achieved by switching the clock-parent to the P_DDRPLLAPSS
(ddrpllapss). Which is set by Qualcomm's proprietary bootcode
as part of the DDR calibration.

For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked
at round 533 MHz (ddrpllsdcc = 190285714 Hz).

whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is
clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

If the a kernel package exists within multiple targets an error/warning
is shown.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: John Crispin <john@phrozen.org>

Signed-off-by: John Crispin <john@phrozen.org>

libext2fs breaks krb5 by always installing its own copies of libcom_err.so
and libss.so.

Move the libraries into separate libcomerr and libss packages respectively
and add a host build recipe to stage the required compile_et and mk_cmds
utilities for use by other packages.

This allows the krb5 package to be fixed to use the system wide libcomerr
and libss libraries.

Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[rename libcom_err to libcomerr, make compile_et and mk_cmds relocatable,
 cleanup makefile, add dependency on host build, reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

c7e938d implement POSIX regexp support
cd6629f lexer: fix encoding 7 bit escape sequences
8614470 main: implement array mode

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

In the commit bde5e7a6 ("kernel: backport mtd implementation for
"compatible" in "partitions" subnode") patches that got accepted into
l2-mtd.git were backported to the kernels 4.9 and 4.14. Unfortunately
there was a regression report, patches were dropped and never reached
4.16.

This commit replaces these pseudo-backports with the latest version
that includes regression fix and futher changes that were requested.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

ae29065 Fix debian/changelog syntax.
6b2b564 Enhance --synth-domain to allow names with sequential integers.
4f7bb57 Fix deletion of dhcp-options from inotify dynamic files.
56f0623 Allow trailing dot in CNAME.
f3223fb Fix nettle_hash() function to avoid ABI incompatibilities.
4c4f4c2 Debian dependency tweaking for new dnsmasq-base-lua package.
773af30 Man page typo fix.
4cc944b Merge branch 'master' of ssh://thekelleys.org.uk/var/local/git/dnsmasq


87e00fe Compiler warning fixes.
e7a4af8 Compiler warning fixes.
2d69d61 Add liblua-dev to Debian build-depends.
30e4a94 Debian package: add dnsmasq-base-lua binary package.
232a8f3 Merge messages for release.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Revert the changes I applied to aa5014dd ("ramips: mt7620n: enable
port 4 as EPHY by default").

The driver expects a node mdio-bus to be present, regardless of the
actual node status. If the node is missing the driver fails to load  with

  mtk_soc_eth 10100000.ethernet: no mdio-bus child node found

Disable port4 by default again. If the port is enabled but not present, a
"invalid port id 4" warning is shown during boot.

Fixes: FS#1428

Signed-off-by: Mathias Kresin <dev@kresin.me>

Support configuration in the form...

    list ip6prefix 2001:db8:1234::/64
    list ip6prefix 2001:db8:5678::/64

... to allow specifying multiple routed IPv6 prefixes.

Implements feature request FS#1361.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>

Switch glibc to 2.26+ [0] and download the sources from git which will it
make easier to update glibc in the future.

For an overview of the fixed bugs and CVE related fixes in 2.26+ see the
NEWS file [1]

[0] https://sourceware.org/git/?p=glibc.git;a=commit;h=d300041c533a3d837c9f37a099bcc95466860e98
[1] https://sourceware.org/git/?p=glibc.git;a=blob;f=NEWS;h=410f0d163145c1549fb73fdd96568f585b5bf62f;hb=refs/heads/release/2.26/master



Signed-off-by: Xinxing Hu <xinxing.huchn@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

Commit f4d9d7a2 removed support for version specific patches; but it also
broke applying of patches in the patches glibc dir.
Fix the issue by setting PATCH_DIR to $(PATH_PREFIX)/patches similar as
musl/common.mk.

Signed-off-by: Xinxing Hu <xinxing.huchn@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>